Miscellaneous Machined Parts
| Product | Item # | Price | |
| PTG Trigger Guard Assembly Winchester 70 Post-64 Short Action Steel in the White |  | $99.99 |
Replacement Trigger Guard for the Winchester 70. Steel in the white. Requires finishing and fitting to firearm.
Technical Information
Notes:
Complete assembly with pushbutton release for floorplate
Requires minor polishing and finishing
Dimensions (may vary slightly due to tolerances in manufacturing):
Thickness at front mounting hole .312"
Thickness at rear mounting hole .176"
Magazine box widest point (where it fits up into the stock) 1.192"
Magazine box narrowest point (where it fits up into the stock) .951"
Back of magazine box to rear of the entire assembly 3.21"
Mounting hole spacing 7 1/16"
Centerline of rear mounting hole to rear of entire assembly .375"
Centerline of front mounting hole to front of entire assembly .55"
Trigger guard area of assembly, width .70"
Mounting hole diameter, both front and rear .266"
Mounting holes are countersunk slightly for mounting screws
| Product | Item # | Price | |
| Broken Shell Extractor Tool |  | 493103 | $119.99 |
This is the base portion of the Broken Shell Extractor only. It is intended for use with the corresponding collet for use with wildcat and other non
Technical Information
Case Head
This is the base portion of the broken shell extractor only. It is intended to be used with the corresponding collet for use with wildcat and other non
General Extractor Notes:
Designed for use when the case head has separated from the case
The base of the steel extractor is shaped like the base of the cartridge case
The front of the extractor is ridged spring steel and slides into the case neck, grasping it
The extractor base can then be grasped (by the rifle's extractor) and the case neck may be pulled out of the chamber
These broken shell extractors are slightly longer than the actual cartridge and are caliber
| Product | Item # | Price | |
| Lathe Centering Buttons Package of 2 |  | 121382 | $33.99 |
These buttons help to set the alignment of a lathe.
Technical Information
Notes:
Steel, .900" diameter, .560" long.
Helps set lathe alignment.
Place buttons between centers, move head and tailstock together until button faces touch. If in alignment, then head and tailstock are aligned.
| Product | Item # | Price | |
| Bushing Tool Colt Double Action Revolver |  | 171014 | $24.99 |
This tool easily slides over the ejector rod to reach the crane bushing for removal without damage in Colt revolvers. For use on Python, Trooper, Officer’s Model, Official Police, Marshal, Cobra, Agent, Police Positive, Detective Special and Pocket Positive.
Technical Information
Notes:
Tool slides over the ejector rod to remove the crane bushing from Colt revolvers.
For use on Python, Trooper, Officer's Model, Official Police, Marshal, Cobra, Agent, Police Positive, Detective Special, Pocket Positive.
| Product | Item # | Price | |
| AR-15 and Sako Extractor Installation Fixture Remington 700 |  | 295966 | $129.99 |
This steel and aluminum tool is used for the installation of an AR
Technical Information
Notes:
For installing an AR
Steel V
Dimensions:(L x W x H)
4 3/4" x 1 3/8" x 2 1/2"
| Product | Item # | Price | |
| Yoke and Mainspring Bending Wedge |  | 348513 | $14.99 |
Polymer wedge gently bends yokes without marring for perfect lock
Technical Information
Notes:
May be used to bend yoke and arch mainspring
Tapers from 1" to 1/8" thick
| Product | Item # | Price | |
| Magazine Lip Gage Beretta 92 |  | 354912 | $38.99 |
Steel gage measures the magazine lip width to ensure proper feeding for the Beretta 92 and M9.
Technical Information
Notes:
Steel, 2 1/2" long
Measures minimum 8.8mm, maximum 9mm magazine lip width.
| Product | Item # | Price | |
| Muzzle Crown Radius Cutter .715" Diameter |  | 352790 | $28.99 |
| Muzzle Crown Radius Cutter .615" Diameter |  | 374259 | $28.99 |
Remove the sharp edge of a newly crowned barrel for a more finished, factory look.
Technical Information
Notes:
Tool steel
Cuts a radius on the outside edge of a barrel after shortening or recrowning.
May be used in a hand drill
| Product | Item # | Price | |
| Rail Swaging Punch Double Rail 1911 |  | 379696 | $28.99 |
Made from machined steel, this punch protects the 1911 rail when making adjustments to the frame.
Technical Information
Notes:
Steel
6 1/2" long, 0.9" diameter
At punch end, two steps are machined into each side of the top, dimensions below apply to either side
First is 0.183" wide, second is 0.118" wide
Height of first step is 0.5", height of second step is 0.14"
| Product | Item # | Price | |
| Extractor Rivet Anvil Remington 700 |  | 385664 | $57.99 |
This Extractor Rivet Anvil is specially designed for Remington 700’s. Slide this hardened steel anvil into the face bolt recess, and it will support the back side of the extractor rivet while "peening" the other end to install a new extractor. Works great if clamped in a vise. 2
Technical Information
Notes:
2 1/4" high x 1 3/4" wide x 1/2" thick
Steel hardened to Rc 60
May be clamped in a vise
Supports back side of extractor rivet while peening rivet
| Product | Item # | Price | |
| Gunsmither Safety Takedown Tool Ruger 10/22, 10/22 Magnum |  | 414743 | $12.99 |
Takedown tools make disassembly simple and easy, helping avoid damage to firearm or user.
Technical Information
Material: Steel with rubber handle
| Product | Item # | Price | |
| Firing Pin Removal Tool Weatherby, SKB |  | 444470 | $14.99 |
Easily removes the firing pin from Weatherby’s and SKB’s with this stainless steel tool. Square end fits onto the rear of the firing pin, and using a 5/16" socket or box wrench, unscrew the firing pin. Stock must first be removed in order to access the rear of the firing pin.
Technical Information
Notes:
1" long, stainless steel, cut to accept 5/16" socket or wrench
Square end fits rear of firing pin to unscrew firing pin
Stock must be removed to access rear of firing pin
| Product | Item # | Price | |
| Broken Shell Extractor Collet 223 Remington Case Head |  | 462502 | $23.99 |
This Collet is intended for use with the corresponding case head portion for use with wildcat and other non
Technical Information
Collet:
This is the neck portion of the broken shell extractor only. It is intended to be used with the corresponding case head portion for use with wildcat and other non
General Extractor Notes:
Designed for use when the case head has separated from the case
The base of the steel extractor is shaped like the base of the cartridge case
The front of the extractor is ridged spring steel and slides into the case neck, grasping it
The extractor base can then be grasped (by the rifle's extractor) and the case neck may be pulled out of the chamber
These broken shell extractors are slightly longer than the actual cartridge and are caliber
| Product | Item # | Price | |
| Barrel Bushing Expander Set 1911 |  | 513609 | $78.99 |
Set allows the rear of a small barrel bushing to be swaged open for a better fit. The swaged bushing can then be turned down to the correct size with the Swenson Barrel Bushing Fitting Mandrel (sold separately).
| Product | Item # | Price | |
| Rail Swaging Punch Single Rail 1911 |  | 529852 | $28.99 |
Made from machined steel, this punch protects the 1911 rail when making adjustments to the frame.
Technical Information
Notes:
Steel
6 1/2" long, 0.9" diameter
At punch end, two steps are machined into the top
First is 0.326" wide, second is 0.228" wide
Height of first step is 0.79", height of second step is 0.185"
| Product | Item # | Price | |
| Grip Bushing Staker 1911 |  | 563977 | $23.99 |
The correct tool for staking 1911 grip bushings. Tool accepts a 1/8" punch and holds it in the correct position for staking.
Technical Information
Notes:
Staker results in a tight, even grip bushing installation.
Support the outside of the bushing with a steel block or anvil when staking.
Staker has a hole in the top for an 1/8" punch.
To use, put bushing in place (support the outside), slide staker into bushing from the inside of the frame using the staker's handle, insert 1/8" punch through the bushing or hole on the opposite side of the frame and down into the staker. The staker has 8 segments with 90 degree cuts for maximum bushing to frame contact.
Tool steel, about 4" overall length.
| Product | Item # | Price | |
| Stock Ferrule Steel Package of 2 |  | 595347 | $5.99 |
Stainless steel ferrule will fit all M98 actions and can be used with any rifle that has a .250” diameter rear stock screw. Perfect for quick pillar bedding applications. Package of 2.
Technical Information
Notes:
M98 ferrule, may be used in any rifle with a .250" diameter rear stock screw
1 1/2" long, .375" outside diameter, .279" inside diameter.
| Product | Item # | Price | |
| Broken Shell Extractor Collet Magnum Case Head |  | 654854 | $23.99 |
This Collet is intended for use with the corresponding case head portion for use with wildcat and other non
Technical Information
Collet:
This is the neck portion of the broken shell extractor only. It is intended to be used with the corresponding case head portion for use with wildcat and other non
General Extractor Notes:
Designed for use when the case head has separated from the case
The base of the steel extractor is shaped like the base of the cartridge case
The front of the extractor is ridged spring steel and slides into the case neck, grasping it
The extractor base can then be grasped (by the rifle's extractor) and the case neck may be pulled out of the chamber
These broken shell extractors are slightly longer than the actual cartridge and are caliber
| Product | Item # | Price | |
| Slide Fitting Bar Holding Fixture |  | 719367 | $23.99 |
Hardened, tool steel bar is used as an anvil inside the frame rails on a 1911. To use, measure the rail thickness on the slide. Then, insert the fitting bar with the same thickness into the frame rails and tap the frame rail gap until it is the correct width to accept the slide. 1" wide x 4" long. Number listed is the thickness of the bar.
Technical Information
Notes:
Steel construction
Measures 2.7" long and 2.2" wide
Includes (2) washers and (2) screws
| Product | Item # | Price | |
| Magazine Lip Forming Tools 1911 45 ACP |  | 721582 | $82.99 |
Tool gently reforms 1911 magazine feed lips to more reliably accept 45 ACP wadcutter ammunition.
Technical Information
Notes:
Reforms magazine feed lips to better feed wadcutter ammunition
Steel
| Product | Item # | Price | |
| Barrel Alignment Block 1911 |  | 722244 | $28.99 |
This steel block features a milled slot to hold a 1911 barrel in its slide for fitting the barrel hood to the bolt face slot. The block is meant to fit between the slide rails to help prevent barrel twisting, and may require minor fitting.
Technical Information
Notes:
Steel, 2" x 3/4" x 1/2"
Milled slot holds the barrel in the slide for fitting the hood to the bolt face slot.
Fits between the slide rails preventing barrel twist
May require minor fitting
| Product | Item # | Price | |
| Bullet Comparator 22, 24, 25, 26, 28, 30 Calibers |  | 746974 | $16.99 |
| Bullet Comparator 17, 20, 22, 27, 30, 33 Calibers | | 365474 | $16.99 |
" Measures from the major diameter of a bullet to the case head, rather than from the bullet's tip to the case head " Steel comparator has six holes cut, one for each caliber listed
Technical Information
Notes:
Allows a comparative measurement from the major diameter of a bullet to the case head, rather than measuring from the bullet's tip to the case head
Comparator is steel and has six holes cut, one for each caliber listed
Insert a cartridge into its correct size hole, then measure from the opposite face of the tool to the base of the cartridge. This dimension may be used to adjust seating dies so that the bullets are being seated more uniformly with respect to the bullet's ogive rather than a cartridge's overall length
| Product | Item # | Price | |
| Barrel Bushing Fitting Mandrel 1911 |  | 749359 | $58.99 |
Bushing installs between 2 halves of the mandrel and can be easily turned down in a drill press or lathe.
| Product | Item # | Price | |
| Shotgun Rib Center Finder |  | 759618 | Price: $14.49 |
Steel fixture locates the exact center of the shotgun rib for installation of a sight bead. 2" x 5/16".
Technical Information
Notes:
2" long, 5/16" square
Locates rib center for sight installation on most shotguns
| Product | Item # | Price | |
| Stuck Choke Removal Tool 12 Gauge |  | 811374 | $90.99 |
Easily remove rusty, stuck choke tubes with this solid steel choke tube wrench. Sturdy T
Technical Information
Notes:
Steel, approximately 4" long
Expandable center section is knurled to grip inner wall of choke.
May damage choke if it is badly rusted in place
| Product | Item # | Price | |
| Upper Receiver Lapping Tool AR-15 |  | 810457 | $21.49 |
Use this lapping tool in a 3/8" electric drill to square the upper receiver face of an AR
Technical Information
Notes:
Use in 3/8" electric drill to square upper receiver face.
Pilot fits in bolt carrier tunnel.
Use with lapping compound.
Steel, 8 1/4" long.
| Product | Item # | Price | |
| Revolver Deburring Tool 1/2" |  | 821348 | $29.99 |
Create a slight radius on the chambers of a revolver cylinder for faster loading. Tool steel.
Technical Information
Notes:
Deburrs chamber edges and barrel throat
Works with 32 through 45 caliber
Aluminum handle, steel cutting ball
| Product | Item # | Price | |
| Pillar Bedding Columns Ruger 77, 77 Mark 2 |  | 874663 | $12.19 |
Columns have been precisely machined with the proper angles for a simple bedding job on the Ruger 77. Aluminum.
Technical Information
Notes:
Aluminum, front .600" long, .535" diameter. Rear 1.145" long, .535" diameter.
Front pillar is cut to match the receiver screw angle, fits against the bottom of the recoil lug.
| Product | Item # | Price | |
| Adjustable Pillar Bedding Column Steel Package of 2 |  | 763473 | $24.49 |
Simple installation, light weight and adjustability make these bedding columns a perfect fit in nearly all types and sizes of rifle stocks. Feature fully threaded shafts for an exact fit without needing to cut, file or machine. Includes a short front pillar and a long rear pillar.
Technical Information
Notes:
Steel sleeve, .296" inside diameter, 7/16"
Requires alteration to stock and bedding for installation.
| Product | Item # | Price | |
| Broken Shell Extractor Collet 308 Winchester Case Head |  | 898503 | $23.99 |
This Collet is intended for use with the corresponding case head portion for use with wildcat and other non
Technical Information
Collet:
This is the neck portion of the broken shell extractor only. It is intended to be used with the corresponding case head portion for use with wildcat and other non
General Extractor Notes:
Designed for use when the case head has separated from the case
The base of the steel extractor is shaped like the base of the cartridge case
The front of the extractor is ridged spring steel and slides into the case neck, grasping it
The extractor base can then be grasped (by the rifle's extractor) and the case neck may be pulled out of the chamber
These broken shell extractors are slightly longer than the actual cartridge and are caliber
| Product | Item # | Price | |
| Muzzle Crown Facing Tool Stop Collar |  | 881376 | $49.99 |
Collar works with the piloted cutter allows for accurate and consistent cutting depths on the face and crown of a barrel.
| Product | Item # | Price | |
| Trimmer Base for L.E. Wilson Case Trimmer |  | 889310 | $16.49 |
This base is constructed of aluminum and measures 5
Technical Information
Material: Aluminum
Dimensions: 5 1/4" x 3" x 1 3/4"
| Product | Item # | Price | |
| Receiver Drilling Fixture Ruger 10/22 |  | 912648 | $38.99 |
This drilling jig permits cleaning a 10/22 from the rear without removing the barrel. It locates the correct spot on the rear of the receiver for a hole to be drilled that allows the cleaning rod to pass through. Helps keep the rifle accurate by eliminating damage done by the cleaning rod when inserted through the muzzle.
Technical Information
Notes:
4" long, steel
Locates cleaning hole location in receiver.
Permits cleaning from the rear without barrel removal.
Requires that a hole be drilled in the rear of the receiver.
Instructions:
Remove the two bolts and fiber washers from the fixture. The 10/22 receiver must be completely disassembled with all parts removed, however the barrel can stay in the receiver. The fixture mounts to the right side of the receiver. Use some suitable material to protect the receiver, then place it on the fixture, lining up the threaded holes in the fixture with the trigger guard retaining pin holes. Use the bolts with the fiber washers to hold the receiver on the fixture. Put the receiver with the fixture in a padded vise, orient it so that the rear of the receiver is facing up. Use a .257" diameter drill bit (this is an "F" drill bit) to drill a hole in the rear of the receiver. Use the bushing in the fixture as a drilling guide. Use Tap Magic to lubricate the bit while drilling. Do not drill more than 1" into the receiver. Deburr the hole with a small file or other tool. This hole will allow a cleaning rod to access the bore from the rear of the receiver. The cleaning hole may be threaded with a 5/16"
| Product | Item # | Price | |
| Wood Stippling Punch 16 Lines Per Inch |  | 912967 | $17.99 |
Used as a quick and easy alternative to hand checkering, this stippling punch will create a customized, non
Technical Information
Notes:
Used as an alternative to checkering.
Pattern is pressed or driven into stock.
| Product | Item # | Price | |
| Barrel Bedding Block |  | 918534 | $12.99 |
When bedding rimfire rifles from the barrel, use this block as a recoil lug and stock bolt retainer. Also serves as an extra forend recoil lug and attachment point for falling block, rolling block and other single shot centerfire rifles.
Technical Information
Notes:
Intended to improve bedding, needed for 10/22 actions with threaded barrel where the barrel lug has been removed.
Use as recoil lug in forend area for other type actions.
May require alteration to rifle for use.
Steel 1.03" x .5" x .475" with .437" radius.
Includes block, escutcheon, 10
| Product | Item # | Price | |
| Hammer Stop Block 1911 |  | 936014 | $33.99 |
Block slides onto rails to facilitate testing of the hammer and trigger without the slide in place. Avoids damage that otherwise might result from dropping the hammer without the slide in place.
Technical Information
Notes:
Aluminum with nylon pad
Fits into frame rails so hammer can be used with slide off frame
| Product | Item # | Price | |
| Barrel Set Back Fixture |  | 954970 | $148.99 |
Fit new barrels, or set back existing barrels to adjust barrel to cylinder gap using this solid steel barrel set back fixture. Can be used without a lathe.
Technical Information
Notes:
Fit new barrels or set back existing barrels to adjust barrel to cylinder gap.
May be used without a lathe.
Steel.
| Product | Item # | Price | |
| Trigger Adjustment Pins Ruger Mark 1, 2 |  | 970862 | $28.99 |
Pins mount to the outside of the firearm, allowing the trigger to be installed on the exterior of the frame. This allows the engagement surfaces to be observed in preparation for stoning. Steel.
Technical Information
Notes:
Steel construction
Used for adjusting the sear and trigger pull
| Product | Item # | Price | |
| Yoke and Mainspring Bending Wedge | | 348513 | $28.99 |
Polymer wedge gently bends yokes without marring for perfect lock
Technical Information
Notes:
Steel construction
Used for adjusting the sear and trigger pull
| Product | Item # | Price | |
| Thread Protector Savage 110 |  | 762354 | $17.99 |
Damaging a barrel's threads will make attachment to the receiver impossible, or at least result in a poor mating with the action and decreased accuracy. A thread protector threads onto a barrel when not in use, protecting the barrel threads from harm during storage.
Technical Information
Notes:
Protects threads on barrel when storing barrel or when performing machining operations
| Product | Item # | Price | |
| Thread Protector Mauser 98 |  | 971862 | $17.99 |
| Thread Protector Remington 700 |  | 799217 | $17.99 |
| Bolt Face Truing Cutter Guide Mauser 1.10" x 12 Thread 60-Degree |  | 515967 | $103.99 |
A bolt face that is truly perpendicular to the bore will result in enhanced accuracy in bolt action rifles. This tool by squares the bolt face to the rifle bore, reducing case stress and enhancing accuracy and reliability. Cutter guides are useful for properly aligning a cutter with a bolt face.
Technical Information
Material: Steel
Notes:
For use with bolt face truing cutters only.
Aligns cutter with bolt face.
| Product | Item # | Price | |
| Bolt Face Truing Cutter Guide Remington and Winchester 70 Classic 1-1/16" x 16 Thread |  | 947969 | $103.99 |
| Bolt Face Truing Cutter Guide Remington 1-1/16" x 16 Thread .010 Oversize |  | 342953 | $103.99 |
| Bolt Face Truing Cutter Guide Savage 10-116 |  | 569853 | $103.99 |
| Bald Eagle Floating Reamer Holder |  | 542929 | $99.99 |
Holder is designed to allow free movement of a floating reamer in 3 directions: vertical, horizontal and angular, as required for proper performance of any floating reamer.
Technical Information
Notes:
Free
Specific for Morse Taper #3 (also available for #2 Morse Taper)
| Product | Item # | Price | |
| Barrel Threading Lathe Bit 60-Degree 1/2" |  | 144052 | $24.99 |
Pre
Technical Information
Material: Steel
Notes:
Preshaped threading lathe bits ready to use.
Notes:
55 degree cutter's are designed to cut the true threads of the 98 Mauser
60 degree cutters duplicate most after market Mauser barrel thread patterns
Square bit cuts a true 12 threads per inch square thread for 03 Springfields and Enfields
Level action| Product | Item # | Price | |
| Barrel Threading Lathe Bit 55-Degree 3/8" |  | 174137 | $24.99 |
| Barrel Threading Lathe Bit 55-Degree 1/4" |  | 586708 | $24.99 |
| Barrel Threading Lathe Bit 55-Degree 1/2" |  | 568592 | $29.99 |
| Barrel Threading Lathe Bit Square 1/2" |  | 359454 | $29.99 |
| Barrel Threading Lathe Bit 55-Degree 5/16" |  | 714728 | $24.99 |
| Barrel Threading Lathe Bit Square 3/8" |  | 367877 | $24.99 |
| Barrel Threading Lathe Bit 60-Degree 3/8" |  | 607918 | $24.99 |
| Barrel Threading Lathe Bit 60-Degree 5/16" |  | 339064 | $24.99 |
| Barrel Threading Lathe Bit Square 1/4" |  | 202793 | $24.99 |
| Barrel Threading Lathe Bit 60-Degree 1/4" |  | 196313 | $24.99 |
| Barrel Threading Lathe Bit Lever Actions 3/8" |  | 394071 | $22.49 |
Pre-shaped threading lathe bits ready to use. The lever action cutter cuts the 12 threads per inch for Marlin lever guns and Remington Rolling blocks.
Technical Information
Material: Steel
Notes:
Preshaped threading lathe bits ready to use.
Notes:
55 degree cutter's are designed to cut the true threads of the 98 Mauser
60 degree cutters duplicate most after market Mauser barrel thread patterns
Square bit cuts a true 12 threads per inch square thread for 03 Springfields and Enfields
Level action cutter cuts the 12 threads per inch found on Marlin lever guns and Remington Rolling Blocks.
| Product | Item # | Price | |
| Bolt Facing Lathe Bit 3/8" |  | 156264 | $18.99 |
Designed with the proper shape to crown barrels.
Technical Information
Notes:
Bit is ground for .210" radius cuts on one end and .250" radius on the other end.
| Product | Item # | Price | |
| Barrel Crowning Lathe Bit 3/8" |  | 469484 | $18.99 |
| Bench Rest Single Shot Follower Remington 700 Long Action |  | 462394 | $21.49 |
Bench rest followers are perfect for competitors, varmint hunters or anyone trying to get the most accuracy possible out of their bolt action rifle. They epoxy in place and allow for simple single shot operation.
Technical Information
Material: Aluminum
Finish: Silver
Features: Stiffens action and offers a loading platform for single feeding
Gunsmithing Required: No
Notes:
May need minor fitting to action cutout
May be epoxied in place if intended as a permanent modification
Short action 2.937" long 1.2oz, Long action 3.784" Long 1.6oz
Fits 308, 30
| Product | Item # | Price | |
| Bench Rest Single Shot Follower Remington 700 Short Action |  | 344951 | $21.49 |
Bench rest followers are perfect for competitors, varmint hunters or anyone trying to get the most accuracy possible out of their bolt action rifle. They epoxy in place and allow for simple single shot operation.
Technical Information
Material: Aluminum
Finish: Silver
Gunsmithing Required: Yes
Notes:
May need minor fitting to action cutout
May be epoxied in place if intended as a permanent modification
Short action 2.937" long 1.2oz, Long action 3.784" Long 1.6oz
For 223 to magnum cartridges
| Product | Item # | Price | |
| Do It Yourself Die Blank 22 Caliber Pilot Hole 7/8 x 14 |  | 314361 | $24.99 |
| Do It Yourself Die Blank 30 Caliber Pilot Hole 7/8 x 14 |  | 118810 | $24.99 |
| Do It Yourself Die Blank 45 Caliber Pilot Hole 7/8 x 14 |  | 493416 | $24.99 |
| Do It Yourself Die Blank 416 Caliber Pilot Hole 7/8 x 14 |  | 820687 | $24.99 |
| Do It Yourself Die Blank Unpiloted 7/8 x 14 |  | 444951 | $24.99 |
| Do It Yourself Die Blank 17 Caliber Pilot Hole 7/8 x 14 |  | 529842 | $24.99 |
| Do It Yourself Die Blank 243 Caliber, 6mm Pilot Hole 7/8 x 14 | | 744472 | $24.99 |
| Do It Yourself Die Blank 25 Caliber Pilot Hole 7/8 x 14 |  | 512398 | $24.99 |
| Do It Yourself Die Blank 264 Caliber, 6.5mm Pilot Hole 7/8 x14 |  | 786397 | $24.99 |
| Do It Yourself Die Blank 270 Caliber Pilot Hole 7/8 x 14 |  | 670952 | $24.99 |
| Do It Yourself Die Blank 284 Caliber, 7mm Pilot Hole 7/8 x 14 |  | 110332 | $24.99 |
| Do It Yourself Die Blank 338 Caliber Pilot Hole 7/8 x 14 | | 124719 | $24.99 |
| Do It Yourself Die Blank 358 Caliber Pilot Hole 7/8 x 14 |  | 823589 | $24.99 |
| Do It Yourself Die Blank 375 Caliber Pilot Hole 7/8 x 14 | | 269691 | $24.99 |
| Do It Yourself Die Blank 20 Caliber Pilot Hole 7/8 x 14 | | 656764 | $24.99 |
Die has a .250" diameter pilot hole and is threaded on the bottom, knurled on top. This is the same style die as used by RCBS and other manufactures. 7/8" x 14 Thread.
Die blanks allow you to cut a die for a custom chamber dimension or to create a new die for a wildcat cartridge. They must be reamed with a die reamer (sold separately) and are pre
Technical Information
Material: 4140 chrome moly steel
Dimensions:
Length = 3.875"
Width = 3/4"
Features:
Standard 7/8" x 14 Thread Size
Knurled Upper
Notes:
Not a finished die. Must be reamed to the cartridge specifications of your choice.
Upper end must be drilled and tapped for internal die parts such as the decapping/expander unit as well as the seater stem (available from RCBS).
Lock ring for setting the die for a desired cartridge length not included (available from RCBS).
Pilot hole of listed caliber drilled through die body
Die body is made of the same material as used by RCBS and other manufacturers. Heat treating is generally not necessary as the die body will last a long time after cutting to the correct dimensions, as the body will then only have contact from the brass cartridge cases. However, if heat treating is desired, heat to 1650
| Product | Item # | Price | |
| Gate Detent Spring Clamp Ruger Single Action Revolver |  | 145866 | $23.99 |
Holds the gate detent spring, releasing pressure from the hammer and trigger pivot pins on Ruger Single Actions. Makes hammer and trigger modifications or replacement easier. Constructed of durable aluminum with a solid steel bolt.
Technical Information
Notes:
Aluminum with steel bolt
Holds gate detent spring, releasing pressure from hammer and trigger pivot pins.
| Product | Item # | Price | |
| Reamer Stop |  | 249610 | $21.49 |
The Reamer Stop is a collar that slips over the shank of a chamber reamer. It is then locked into place using the set screws. The Reamer Stop prevents cutting too deep. Fits and ECT chamber reamers.
Technical Information
Material: Steel
Notes: A great tool designed to attach to the shaft of your reamer to assure you do not cut to deep. Attaches to the reamer with one allen head screw. (wrench not included)
P.T.G. (Pacific Tool and Grinding):
Fits
3/8" (9.5 mm) square drive shank reamers
| Product | Item # | Price | |
| T-Handle Reamer Extension |  | 775160 | $37.99 |
This 12" Extension fits any ECT or reamer. It allows the reamer to be used when a standard tap handle will not work.
Technical Information
Notes:
Steel extension is 12" long and fits and other reamers with a 3/8" square drive shank.
| Product | Item # | Price | |
| Magazine Follower Mossberg 12 Gauge Aluminum Red |  | 644129 | $19.49 |
| Magazine Follower Remington 12 Gauge Aluminum Green |  | 915162 | $19.49 |
| Magazine Follower Benelli 12 Gauge 3" Chamber Aluminum Black |  | 815398 | $19.49 |
| Magazine Follower Mossberg 12 Gauge Aluminum |  | 772300 | $19.49 |
Replacement magazine follower is more durable than the factory plastic part. Drop
Technical Information
Notes:
Direct replacement for factory magazine follower
Requires disassembly and reassembly of shotgun, fit is the same as the factory follower
| Product | Item # | Price | |
| Sight Base File 65-Degree 1911 |  | 992408 | $12.49 |
Designed to finish a 65 degree dovetail sight cut to remove burrs and ensure a perfect sight fit.
Technical Information
Notes:
File has one cutting side and two safe sides
3/16" x 7"
| Product | Item # | Price | |
| Barrel Centering Bar |  | 110214 | $79.99 |
This hardened steel bar centers the bore of a rifle barrel to a lathe. It will work for up to 45 caliber barrels.
Technical Information
Notes:
7" long, 1/2" diameter, fits up to .45 caliber.
Centers bore of rifle barrel to lathe.
Hardened steel.
| Product | Item # | Price | |
| Lathe Centering Bar 1" x 8" |  | 541184 | $83.99 |
This steel centering bar allows the alignment of a lathe to be checked.
Technical Information
Notes:
Allows checking alignment of lathe.
Recesses on each end align headstock and tailstock centers.
Aids in offsetting tailstock for taper cutting.
Steel.
| Product | Item # | Price | |
| Barrel Spinner |  | 543792 | $99.99 |
Use this spinner to polish barrels up to 32" long and magazine tubes. Simple to use, just secure the barrel between the non
Technical Information
Notes:
Use to polish barrels and magazine tubes.
Barrel is secured between Delrin centers.
To use, secure barrel in place, then hold spinner and place barrel against a motorized buffing wheel. The barrel will rotate in the spinner and can then be moved around for even polishing.
Aluminum frame is 36" long, will accept up to 32" long barrels.
Support arms are 4 1/2" long, secured with socket head lock screws, 1 1/2" spacing from barrel to spinner.
| Product | Item # | Price | |
| Back Bore and Choke Reamer Handle 34" |  | 692058 | $29.99 |
For use with the Back Bore Reamers only. Measures 34" long.
Technical Information
Notes:
Handle for use with back bore reamers and carbide choke reamers in shotgun barrels.
Steel.
| Product | Item # | Price | |
| Bedding Fixture M1 Garand |  | 360279 | $48.99 |
This fixture gives the barrel, receiver and trigger group the correct positioning during the bedding process. Trigger guard is held partially open by the steel U
Technical Information
Notes:
Fixture gives barrel, receiver and trigger group the correct positioning when bedding.
Trigger guard is held partially open by U
Barrel is centered in channel by spacer.
U
Spacer is aluminum, 1 1/8" x 1 1/16", 3/8" thick
| Product | Item # | Price | |
| Bedding Fixture M1A |  | 365927 | $38.99 |
This fixture gives the barrel, receiver and trigger group the correct positioning during the bedding process. Trigger guard is held partially open by the steel U
Technical Information
Notes:
Trigger guard is held partially open by U
U
Spacer is aluminum, 1 1/2" diameter, 2 1/2" long
| Product | Item # | Price | |
| Bolt Face Lapping Tool M1A, M1 Garand |  | 168507 | $59.99 |
Technical Information
Notes:
Tool is spring loaded, keeps constant pressure on bolt lugs.
Use with 600 to 800 grit lapping compound, not included.
Includes bolt tool body, plunger and sleeve.
| Product | Item # | Price | |
| Barrel Hone Extension Shaft 12, 16, 20 Gauge |  | 515300 | $74.99 |
This 28" long steel shaft gives you the extra reach you need to clean the full length of a shotgun bore using an electric drill. Faster, better results since the pilot will keep the hone centered. Includes 2 nylon pilots.
Technical Information
Notes:
Steel shaft 28" long, 1/4" diameter
Two nylon pilots, each .715" diameter
Intended for use with electric drill
| Product | Item # | Price | |
| Headspace Ring 12 Gauge |  | 198712 | $8.49 |
| Headspace Ring 20 Gauge |  | 242148 | $8.49 |
Steel ring measures 1/4" long and is soldered into the shotgun chamber. Then the chamber rim is recut with a rim cutter.
Technical Information
Notes:
Steel, 1/4" long
For use with rim cutter, intended to be soldered into shotgun chamber and then chamber rim area is recut.
0.785" inside diameter, 0.884" outside diameter, 0.048" thick, 0.310" wide
| Product | Item # | Price | |
| Disconnect Scraper 1911 |  | 290788 | $14.49 |
Hardened steel scraper deepens the disconnector notch to allow proper function.
Technical Information
Notes:
Designed to cut the disconnector notch deeper so the disconnector won't hit the slide.
Steel scraper with plastic handle, approximately 5" long.
| Product | Item # | Price | |
| Decorative Sight Slot Blank 3/8" Dovetail Steel Blue |  | 128446 | $16.99 |
Finished blank fills the dovetail slot left when a sight is removed. Gunsmith blank is offered for custom applications and will require fitting and finishing.
Technical Information
Notes:
Fills space when a sight has been removed.
May be shaped with a file and touched up with cold blue if needed.
| Product | Item # | Price | |
| Ejector Rod Housing Arbor Ruger, Colt Single Action |  | 690464 | $9.99 |
Hold ejector rod housing securely to the lathe with this steel arbor. Designed with an Allen screw head to help keep the ejector rod square during cutting. Great for trimming to the right length.
Technical Information
Notes:
Steel, 1/4" diameter, 5 1/16" long
Holds ejector rod housing when cutting to a different length
Allen screw head fits into hole in housing, prevents rotating when cutting the housing shoulder
| Product | Item # | Price | |
| Adjustable Extractor Support Removal Tool 44 and 45 Calibers |  | 297893 | $28.99 |
| Adjustable Extractor Support Removal Tool 38 Special and 357 Magnum |  | 170643 | $28.99 |
Eliminate the need for different tools to fit different guns with this adjustable extractor support removal tool. Brass support rod fits in the rear of the cylinder and supports the extractor guide pin and star when the ejector rod is unscrewed. Body is solid, carbon steel.
Technical Information
Notes:
Brass support rods fit in rear of cylinder and support extractor guide pin and star when ejector rod is unscrewed.
Steel body approximately 3" long, brass rods.
| Product | Item # | Price | |
| Firing Pin Protrusion Gage |  | 515390 | $29.49 |
Accurately and easily measure rimfire and centerfire firing pin protrusions to within 0.0001" with the Baker Firing Pin Extrusion Gage. To use, simply unlock the plunger and place the gage over an extended firing pin. Lock the plunger and then measure the overall length with a micrometer. The difference between the original length and the overall length on the body, plus the plunger, is the amount of protrusion from the firing pin. Great way to see if a firing pin spring is getting weaker over time.
Technical Information
Notes:
0.90" plunger, hardened
Body is 1/2" diameter
Gage will measure rimfire and centerfire firing pin protrusion to within 0.0001"
For use, unlock plunger and place gage over firing pin (extended), lock plunger and then measure overall length with a micrometer. The difference between the original length and the overall length of the body plus the plunger is the amount of firing pin protrusion.
| Product | Item # | Price | |
| Single Action Gas Ring Stretcher |  | 119834 | $85.99 |
Stretcher contains sturdy steel jaws that swage and widen the gas ring in front of the cylinder, reducing barrel leading when using lead bullets. Requires a large bench vise for use.
Technical Information
Notes:
Steel jaws swage gas ring for a tighter frame to cylinder fit
Requires a large bench vise for use
Stretcher jaws, support pin with handle and sleeve are included
| Product | Item # | Price | |
| Base Pad Removal Tool Glock |  | 333867 | $19.49 |
Removing base pads from Glock factory magazines is simple with these specially designed pliers. Plier tips contact the magazine above the base pad locking tabs, compress slightly and slide the pad off. Designed to prevent damage and over compression of the magazine sidewalls.
Technical Information
Notes:
Plier tips contact the magazine above the base pad locking tabs.
Slightly compress the magazine body and then remove the base pad.
Approximately 6" overall length.
| Product | Item # | Price | |
| Gunsmith's Trigger Weight Set |  | 265614 | $179.99 |
This weight set will measure trigger pull from 2 lbs to 17
Technical Information
Notes:
Rod is 12" long, weights are 2" diameter
Set will measure trigger pulls from 2 lb to 17 3/4 lb
Set Includes:
Rod
One 1/4 lb weight
One 1/2 lb weight
Two 1 lb weights
One 3 lb weight
Two 5 lb weights
Base, weighs 2 lb
| Product | Item # | Price | |
| Hammer Squaring File 1911 |  | 291157 | $33.99 |
File is precision-ground with 2 safe sides for a perfect hammer hook angle.
Technical Information
Notes:
5" long, tapers from .185" to .180"
Two sided square file for cutting precise 90 degree hammer hook angle
| Product | Item # | Price | |
| Sear Tool 1911 |  | 955975 | $98.99 |
Aluminum fixture combines a sear jig and a 25x magnifier to produce match
Technical Information
Notes:
Aluminum, 3" x 1.5" x 3/4"
Sear stoning fixture allows cutting of both primary and secondary sear angles.
| Product | Item # | Price | |
| Baker Hammer, Sear Pin Block Kit |  | 970388 | $126.99 |
Precision-machined block holds the hammer and sear pin as they would sit in the trigger group, allowing engagement surfaces to be observed. Ideal for all kinds of trigger work. Kit includes the block and all pins listed.
Technical Information
Notes:
Allows positioning of the hammer and sear for observing the engagement point between them.
Dovetail adjustment block moves in slotted channel for pin positioning.
Allen screw locks the pin setting.
Block is steel, pins are stainless steel
Includes block, and a set of hammer and sear pin for the following firearms:
1911, Colt Single Action Army, Uberti Cattleman, Ruger 10/22, Ruger New Model Single Action, Ruger Mark 2, Browning Hi
| Product | Item # | Price | |
| Hammer Slot Stone 1911 |  | 569769 | $11.99 |
This India stone is sized to fit inside the 1911 hammer slot. .300" x .500" x 6".
Technical Information
Notes:
Ceramic, .300" square, 5" long
Smooths inside surface of 1911 frame where hammer rides on frame surface
| Product | Item # | Price | |
| Hammer and Trigger Fixture AR-15 |  | 213753 | $51.99 |
Test fire any AR
Technical Information
Notes:
Allows testing of AR
Trigger group is held on the side of the lower receiver.
Aluminum, fits .154" diameter pin holes.
| Product | Item # | Price | |
| Magazine Feed Lip Tool AR-15 |  | 989053 | $11.29 |
Repair bent, or out of shape magazine feed lips, and help prevent jams and feeding problems with this easy to use tool. Specifically designed to bend the feed lips back to the correct angle without the costly and unsightly damage to the magazine that pliers or pry bars can do. Steel shank is beveled with a cut slot that fits onto and supports the feed lips during this process. Helps restore old magazines back to original condition.
Technical Information
Notes:
Plastic handle, steel shaft, 5 1/2" total length.
Tool is used to bend feed lips into place without damage.
| Product | Item # | Price | |
| Lug Iron 1911 |  | 821643 | $47.99 |
This tool is useful for removing the ridges and wear marks from a 1911 slide's lug area. At 9" long with a large plastic handle, this tool provides plenty of leverage for the task at hand.
Technical Information
Notes:
Steel shaft and head, plastic handle
Approximately 9" long
Head removes ridges and wear marks from the slide lug area
| Product | Item # | Price | |
| Magazine Well Filler Extended 1911 |  | 769908 | $28.99 |
Aluminum fixture inserts into the magazine well, preventing the frame from being crushed when clamped in a vise.
Technical Information
Notes:
Aluminum
Fits inside the magazine well area to protect frame from damage when frame is held in a vise
| Product | Item # | Price | |
| Magazine Well Filler Browning Hi-Power |  | 328418 | $33.99 |
Aluminum fixture inserts into the magazine well, preventing the frame from being crushed when clamped in a vise.
Technical Information
Notes:
Aluminum
Fits inside the magazine well area to protect frame from damage when frame is held in a vise
| Product | Item # | Price | |
| Magazine Well Filler STI Double Stack |  | 510626 | $23.99 |
Aluminum fixture inserts into the magazine well, preventing the frame from being crushed when clamped in a vise.
Technical Information
Notes:
Aluminum
Fits inside the magazine well area to protect frame from damage when frame is held in a vise
| Product | Item # | Price | |
| Mainspring Compressor Ruger, Colt, S&W, Taurus, H&R Revolvers with Coil Mainspring |  | 715675 | $48.99 |
For disassembling and reassembling revolvers, this tool helps with the removal or installation of the retaining pin. Works with Ruger, Colt, S&W, Taurus, and H&R Revolvers with a coil mainspring. Also works great on Ruger #1 and #3 rifles. Features a steel blue finish.
Technical Information
Notes:
6.25" long, 1" wide
Controls mainspring and strut for retaining pin removal and installation.
May also be used for Ruger #1 and #3 rifles.
| Product | Item # | Price | |
| Mainspring Pusher Ruger Mark 1,2 |  | 844380 | $58.99 |
Pusher provides complete control when removing and replacing the latch pin.
Technical Information
Notes:
Steel, 1 1/4" thick, 3 1/4" long
Punch controls compression, block holds mainspring housing so latch pin is removed or installed.
| Product | Item # | Price | |
| Mainspring Housing Pin Removal Tool 1911 |  | 478800 | $23.99 |
This dedicated, purpose
Technical Information
Notes:
Use to drive out mainspring housing pin
Steel with plastic handle
| Product | Item # | Price | |
| Slide Micrometer 1911 |  | 323990 | $179.99 |
Micrometer is specifically designed to measure the thickness of frame rails. Measures from .0000 to .4265". 2
Technical Information
Notes:
Measures thickness of slide rails
Stainless steel, reads .0000" to .4265", 2 1/2" overall length
| Product | Item # | Price | |
| Plunger Tube Support 1911 |  | 143231 | $14.99 |
This tool uses a hardened point to flare the plunger tube legs into the recesses in the frame. Works with most 1911 frames, including Officer. Requires a crescent wrench for use (not included). Support is used to avoid damage to the plunger tube during staking.
Technical Information
Notes:
Steel, 4" long, .106" diameter, with step of .3" at .09" diameter
Prevents damage to plunger tube when tube is staked to frame
| Product | Item # | Price | |
| Rivet Staking Punch Set 2-Piece Remington 870 |  | 143322 | $24.49 |
Make fitting the ejector spring housing of a Remington 870 easy with these specially designed punches. One tool fastens the ejector housing to the lower portion of the rivet, the other fits the upper part of the rivet to hold the ejector spring in the ejector housing.
Technical Information
Notes:
Fastens ejector housing to lower portion of the rivet, then fits the upper part of the rivet to hold the ejector spring in the ejector housing.
| Product | Item # | Price | |
| Roll Pin Holder 1/16" |  | 881408 | $13.99 |
This steel shaft with a hollow end will hold roll pins perfectly aligned for correct starting. Works great for small pins or hard
Technical Information
Notes:
Steel shaft with hollow end to start a roll pin into place. Finish driving roll pin with a roll pin punch.
Holder is approximately 4 1/2" overall length
Size in the description is the diameter of the tip of the holder
| Product | Item # | Price | |
| Roll Pin Holder 1/8" |  | 144208 | $13.99 |
This steel shaft with a hollow end will hold roll pins perfectly aligned for correct starting. Works great for small pins or hard
Technical Information
Notes:
Steel shaft with hollow end to start a roll pin into place. Finish driving roll pin with a roll pin punch.
Holder is approximately 4 1/2" overall length
Size in the description is the diameter of the tip of the holder
| Product | Item # | Price | |
| Roll Pin Holder 3.5mm |  | 334883 | $13.99 |
This steel shaft with a hollow end will hold roll pins perfectly aligned for correct starting. Works great for small pins or hard
Technical Information
Notes:
Steel shaft with hollow end to start a roll pin into place. Finish driving roll pin with a roll pin punch.
Holder is approximately 4 1/2" overall length
Size in the description is the diameter of the tip of the holder
| Product | Item # | Price | |
| Roll Pin Holder 3/32" |  | 233579 | $13.99 |
This steel shaft with a hollow end will hold roll pins perfectly aligned for correct starting. Works great for small pins or hard
Technical Information
Notes:
Steel shaft with hollow end to start a roll pin into place. Finish driving roll pin with a roll pin punch.
Holder is approximately 4 1/2" overall length
Size in the description is the diameter of the tip of the holder
| Product | Item # | Price | |
| Roll Pin Holder 5/64" |  | 243219 | $13.99 |
This steel shaft with a hollow end will hold roll pins perfectly aligned for correct starting. Works great for small pins or hard
Technical Information
Notes:
Steel shaft with hollow end to start a roll pin into place. Finish driving roll pin with a roll pin punch.
Holder is approximately 4 1/2" overall length
Size in the description is the diameter of the tip of the holder
| Product | Item # | Price | |
| Round Butt Fitting Guide S&W K, L-Frame |  | 263717 | $23.99 |
1/4" hardened steel plate lets you change a S&W K or L
Technical Information
Notes:
1/4" thick hardened steel plate
May require alteration of strain screw
Pattern allows changing square butt revolvers into round butt type
| Product | Item # | Price | |
| Rimfire Receiver Sight Base Mossberg 35, 42, 44, 45, 46 |  | 774658 | $22.99 |
Specially designed to be installed without having to drill or tap the receiver, this steel sight base is machined for Williams Target Foolproof and Lyman MJT receiver sights.
Technical Information
Notes:
1 3/4" x 3/8"
Steel base for installation on receiver.
Machined for Williams Target Foolproof, Lyman MJT receiver sights.
Designed for installation without drilling and tapping receiver.
| Product | Item # | Price | |
| Shotgun Barrel Caliper Steel |  | 264669 | $59.99 |
The Shotgun Barrel Caliper is an easy to use tool that allows a measurement of metal removal when working on shotgun bores. Insert one end into the bore and open, then, the other end is measured with standard calipers or a micrometer (not included). The tool does not have any index or measuring marks, but will work with all gauges.
Technical Information
Notes:
6 1/2" long
Works with all gauges
Allows a measurement of metal removal when working on shotgun bores
One end is inserted into bore and opened, then the other end is measured with standard calipers or a micrometer
This tool itself does not have any index or measuring marks
| Product | Item # | Price | |
| Shotgun Bead Facing Cutter #1 .099" Diameter |  | 915680 | $28.99 |
This cutter will trim the base of the bead at a 90 degree angle so the bead is square with the shank. Keeps the bead from looking sloppy or tilted for a professionally installed look. Cutter employs a drilled hollow center to accept a bead shank and is 3
Technical Information
Notes:
Cutter with drilled hollow center to accept bead shank.
Cuts the base of the bead at a 90 degree angle so the bead is square with the shank.
Overall length 3 1/2", handle is approximately 1 1/8" diameter.
| Product | Item # | Price | |
| Shotgun Barrel Wall Thickness Gage |  | 164349 | $94.99 |
Accurate to 0.001", place this gage in a vise and slide the barrel over the bottom rod and the indicator will give the barrel wall thickness. Steel and aluminum construction, tool is 18
Technical Information
Notes:
Steel and aluminum construction
18 3/4" long, 5" high
For use, place gage in a vise and slide barrel over bottom rod. Dial indicator will give thickness to .001"
| Product | Item # | Price | |
| Shotgun Chamber Gage Handle |  | 152359 | $12.49 |
Use with Shotgun Chamber Gages. Allows for easier removal and insertion of the gage.
Technical Information
Notes:
1/4
| Product | Item # | Price | |
| Slide Rail File 1911 |  | 519541 | $30.99 |
File is designed to clean up and square the slide rails on a 1911.
Technical Information
Notes:
1/2" wide, 6" long
Cleans slide rails and channels.
| Product | Item # | Price | |
| Single Shot Magazine Adapter Winchester 52, 69, 75 |  | 371207 | $38.99 |
Steel adapter allows for single rounds to be dropped into the rifle without loading the magazine. Lightweight aluminum construction.
Technical Information
Notes:
Steel adapter top allows rounds to be dropped into the rifle without loading in the magazine.
Aluminum body.
| Product | Item # | Price | |
| Tap Guide |  | 228592 | $26.99 |
Tap guide works for both flat and curved surfaces, aligning the tap with the hole. Accepts taps from 3/8" to 0
Technical Information
Notes:
Aligns tap with hole.
Will work on flat or round surfaces.
Set accepts tap sizes from 3/8" to 0
Steel.
| Product | Item # | Price | |
| Trigger Track Stone 1911 |  | 457592 | $15.49 |
Ceramic stone is .230" square and 5" long. Designed specifically to remove burrs and machining marks from a 1911 trigger track.
Technical Information
Notes:
Fits inside the trigger frame cuts, polishes rough edges
Ceramic stone, .230" square, 5" long
| Product | Item # | Price | |
| Trigger Group Bedding Block Mauser 98 Large Ring |  | 119168 | $28.99 |
| Trigger Group Bedding Block Remington 700 | | 562493 | $28.99 |
Polymer block replaces the trigger group when bedding a barrel, avoiding the need to wrap the trigger group or fill with clay. Coat the block with release agent before bedding to ensure easy removal with no mess.
Technical Information
Notes:
Delrin construction
This tool is used to keep glass bedding compound out of your stock when bedding your gun
Dimensions:( W x H x Thickness)
1.5" x 2.25" x 29/64"
| Product | Item # | Price | |
| Trigger Stirrup Die 1911 |  | 619774 | $23.99 |
Steel die slips into the trigger stirrup and is used like an anvil to smooth out the factory stirrup. Produces and maintains the correct stirrup geometry for a perfect 1911 trigger job.
Technical Information
Notes:
Use to smooth out production triggers
Slide trigger over die, tap around trigger to smooth stirrup
Steel
| Product | Item # | Price | |
| Trigger Adjustment Pins 1911 |  | 795641 | $28.99 |
Pins mount to the outside of the gun, allowing the trigger components to be assembled exactly as they would sit in the gun. This allows the engagement surfaces to be easily observed in preparation for stoning or adjustment.
Technical Information
Notes:
Tool steel
Mount on the frame so that trigger pull and sear engagement may be checked without repeated assembly and disassembly of the 1911.
| Product | Item # | Price | |
| Trigger Adjustment Pins Ruger Single Action Revolver |  | 731060 | $28.99 |
Pins mount to the outside of the firearm, allowing the trigger to be installed on the exterior of the frame. This allows the engagement surfaces to be observed in preparation for stoning. Steel.
Technical Information
Notes:
Steel construction
Used for adjusting the sear and trigger pull
| Product | Item # | Price | |
| Trigger Group Assembly Tool M1 Garand, M1A |  | 810958 | $59.99 |
Fixture holds the hammer, plunger and spring so the pin can be removed or inserted easily. Drilled holes in the base allow the assembly to be mounted to a work bench.
Technical Information
Notes:
Holds hammer, plunger and spring so the pin can be removed or inserted.
Fixture is drilled for attaching to a bench.
| Product | Item # | Price | |
| Yoke and Crane Reamer .310" S&W k, l, N-Frame, Ruger Six Series |  | 595295 | $33.99 |
Restore the inside dimension and free up the ejector springs in S&W K, L, and N
Technical Information
Notes:
Used to resize diameter and remove burrs and rough patches
| Product | Item # | Price | |
| Yoke and Crane Alignment Tool Ruger Six Series |  | 386768 | $28.99 |
This tool detects any misalignment due to a bent yoke on both Ruger and S&W revolvers. Allows adjustment for more consistent crane lock
Technical Information
Notes:
This tool allows precision crane alignment
Tool is 3.025" long, fits Ruger Security Six, Speed Six, Service Six, knurled end may need to be shortened to fit 2 1/2" barrel
| Product | Item # | Price | |
| Yoke and Crane Alignment Tool S&W J-Frame |  | 273068 | $28.99 |
This tool detects any misalignment due to a bent yoke on both Ruger and S&W revolvers. Allows adjustment for more consistent crane lock
Technical Information
Notes:
This tool allows precision crane alignment
Tool is 2.6" long, use on centerfire revolvers
| Product | Item # | Price | |
| Yoke and Crane Alignment Tool S&W K, L, N-Frame |  | 594137 | $28.99 |
This tool detects any misalignment due to a bent yoke on both Ruger and S&W revolvers. Allows adjustment for more consistent crane lock
Technical Information
Notes:
This tool allows precision crane alignment
Tool is 3.17" long.
| Product | Item # | Price | |
| Upper Receiver Milling Fixture AR-15 |  | 819480 | $26.99 |
Securely hold an upper receiver to a vise with this aluminum, non
Technical Information
Notes:
Fits in vise to hold upper receiver.
Bar fits in bolt carrier recess.
Socket head screws (1/4
Receiver may be secured with or without barrel installed.
Aluminum, bar is 7 1/2" long, block is 5" x 1" x 1"
| Product | Item # | Price | |
| Revolver Cutter Tool Handle |  | 636715 | $12.49 |
Tool steel cutter is used in conjunction with a nominal pilot bushing (sold separately) to adjust the barrel to cylinder gap, as well as to square the rear of the barrel face.
Technical Information
Notes: (from the manufacturer)
Cutter Tool Handle for ECT/ Revolver Cutter
| Product | Item # | Price | |
| Lambeth-Kiff Micrometer Adjustable Reamer Stop |  | 894766 | $188.99 |
This 8 piece kit makes chambering a barrel easier, and is for use by experienced gunsmiths and machinists only. Detailed instructions are included.
Technical Information
Notes:
8
Each body has four laser
Each body fits standard .4375 reamer shank and are counter
Each body is threaded 40tpi for .500
Micrometer dial has 25 even
Micrometer dial has approximately .250 adjustment with each body
There are extensive and well written instructions for the use of this product
This is intended for use by professional gunsmiths and machinists only
| Product | Item # | Price | |
| Barrel Cylinder Alignment Gage 22 Rimfire |  | 821726 | $23.99 |
| Barrel Cylinder Alignment Gage 22 Rimfire S&W K-22 | | 198754 | $23.99 |
| Barrel Cylinder Alignment Gage 32 Caliber | | 147397 | $23.99 |
| Barrel Cylinder Alignment Gage 38, 357 Caliber Match | | 164421 | $23.99 |
| Barrel Cylinder Alignment Gage 41 Caliber | | 356584 | $23.99 |
| Barrel Cylinder Alignment Gage 44 Caliber | | 469545 | $23.99 |
| Barrel Cylinder Alignment Gage 45 Caliber | | 210976 | $23.99 |
Gage ensures proper alignment between revolver cylinder and barrel.
Technical Information
Notes:
This tool is used to properly align the center of the bore and the firing pin to avoid off
| Product | Item # | Price | |
| Barrel Cylinder Alignment Gage Handle |  | 825728 | $11.99 |
For use with Barrel Cylinder Alignment Gages only.
Technical Information
Notes:
Handle threads to any barrel cylinder alignment gage so the gage may be placed in position down the barrel of a revolver
| Product | Item # | Price | |
| Barrel Bushing Expander Set 1911 | | 513609 | $78.99 |
Set allows the rear of a small barrel bushing to be swaged open for a better fit. The swaged bushing can then be turned down to the correct size with the Swenson Barrel Bushing Fitting Mandrel (sold separately).
| Product | Item # | Price | |
| Revolver Forcing Cone Plug Gage 22 Rimfire 11 Degree |  | 461566 | $34.99 |
| Revolver Forcing Cone Plug Gage 32 Caliber 11 Degree, 18 Degree | | 180992 | $34.99 |
| Revolver Forcing Cone Plug Gage 357 Caliber 5 Degree | | 969902 | $34.99 |
| Revolver Forcing Cone Plug Gage 38/357 Caliber 11 Degree, 18 Degree | | 626996 | $34.99 |
| Revolver Forcing Cone Plug Gage 40 Caliber 11 Degree, 18 Degree | | 615819 | $34.99 |
| Revolver Forcing Cone Plug Gage 41 Caliber 11 Degree, 18 Degree | | 718433 | $34.99 |
| Revolver Forcing Cone Plug Gage 44 Caliber 11 Degree, 18 Degree | | 122876 | $34.99 |
| Revolver Forcing Cone Plug Gage 44 Caliber 5 Degree | | 875727 | $34.99 |
| Revolver Forcing Cone Plug Gage 45 Caliber 11 Degree, 18 Degree | | 821836 | $34.99 |
| Revolver Forcing Cone Plug Gage 45 Caliber 5 Degree | | 787576 | $34.99 |
| Revolver Forcing Cone Plug Gage S&W K Frame 38 Caliber 9 1/2 Degree | | 898403 | $34.99 |
| Revolver Forcing Cone Plug Gage S&W L Frame 38 Caliber 9 1/2 Degree | | 998324 | $34.99 |
Gage measures the depth of the forcing cone and shows when it is cut correctly. Match the angle to the angle of the forcing cone cutter being used.
Technical Information
Notes:
Hardened steel gage is is inserted into the barrel to check whether the forcing cone has been cut to a particular angle
Gages listing two angles will measure either one
These gages are approximately 1 1/2" long
| Product | Item # | Price | |
| Slide Fitting Bar 1911 .111" |  | 187202 | $23.99 |
| Slide Fitting Bar 1911 .112" | | 653674 | $23.99 |
| Slide Fitting Bar 1911 .113" | | 394752 | $23.99 |
| Slide Fitting Bar 1911 .114" | | 163797 | $23.99 |
| Slide Fitting Bar 1911 .115" | | 967423 | $23.99 |
| Slide Fitting Bar 1911 .116" | | 159811 | $23.99 |
| Slide Fitting Bar 1911 .117" | | 290849 | $23.99 |
| Slide Fitting Bar 1911 .118" | | 418831 | $23.99 |
| Slide Fitting Bar 1911 .119" | | 754891 | $23.99 |
| Slide Fitting Bar 1911 .120" | | 191746 | $23.99 |
Hardened, tool steel bar is used as an anvil inside the frame rails on a 1911. To use, measure the rail thickness on the slide. Then, insert the fitting bar with the same thickness into the frame rails and tap the frame rail gap until it is the correct width to accept the slide. 1" wide x 4" long. Number listed is the thickness of the bar.
Technical Information
Notes:
4" x 1" x thickness listed in description
Hardened tool steel
For use, measure the slide rail thickness, place slide fitting bar (use closest thickness to measurement) in frame, then press or tap frame rail to close the space to match the slide rail thickness.
| Product | Item # | Price | |
| Bolt Lug Lapping Tool Remington 700 |  | 781097 | $35.99 |
Bolt locking lugs cam and lock into corresponding lug recesses in the receiver as the bolt is closed. For the smoothest operation of the bolt and utmost accuracy, both lugs should be smooth and in full contact with the corresponding lug recesses. In factory production rifles and in surplus military rifles, this is the exception, rather than the rule. Before final headspacing, simply thread this tool into the receiver threads, apply lapping compound to the bolt lugs, then open and close the bolt to lap the lugs smooth and into perfect contact with the lug recesses.
Technical Information
Material:
Tool Steel
Notes:
Increases accuracy by allowing the user to lap the bolt lugs to insure that both lugs are bearing evenly on their recesses.
Screws into receiver threads (barrel must be removed)
600 grit polish is applied to the bolt lugs and the bolt closed against the spring loaded center pilot of the tool. Raising and lowering the rifle's bolt repeatedly will polish the lugs for a better, more crisp feel.
Must be done before final headspacing| Product | Item # | Price | |
| Bolt Lug Lapping Tool Mauser 98 Large Ring |  | 383558 | $35.99 |
| Bolt Face Lapping Tool Mauser 98 Large Ring |  | 866125 | $34.99 |
| Bolt Face Lapping Tool Remington 700 |  | 493220 | $49.99 |
| Bolt Face Lapping Tool Savage 110 |  | 795229 | $49.99 |
| Bolt Face Lapping Tool Mauser 93, 94, 95, 96 |  | 448353 | $49.99 |
For the utmost in accuracy, the bolt face should be perpendicular (square) to the centerline of the bore and chamber. On production rifles, no special attention is normally given to the squareness of the bolt face as it relates to the chamber, which provides the gunsmith with another opportunity to improve the accuracy of a factory rifle. To use this tool, simply screw it into the receiver threads, apply polishing compound to the face of the mandrel and use a 3/8" electric drill to turn the mandrel and polish the bolt face square to the centerline of the bore.
Technical Information
Material:
Tool Steel
Notes:
Screws into receiver threads (barrel must be removed)
3/8" hand
Must be done before final headspacing
Lap is .475" diameter to fit 243, 308, 30
Lap center shaft length 4"
| Product | Item # | Price | |
| Interchangeable Pilot Muzzle and Cylinder Chamfering and Crowning Cutter Handle |  | 143522 | $11.99 |
For use with the Interchangeable Pilot Muzzle and Cylinder Chamfering Cutter only.
| Product | Item # | Price | |
| Slide Milling Fixture 1911 |  | 327842 | $119.99 |
Milling fixture secures slides firmly in place for all types of milling projects.
Technical Information
Notes:
Material: Solid aluminum
Use: Milling
Dimensions: 5¾" (14.6cm) long, 2" (10cm) wide 1 lb. 10 oz. (759g)