picture

Reloading Tools

 

Misc. Reloading Tools

Not seeing what you are looking for? Click here to submit a request for quote for a custom endmill

 

Universal & Caliber Specific Die Blanks
Bullet Comparator
Bullet Comparator

 

~Top of Page~

  • Misc. Reloading
    Tools
  • More
    Coming Soon!

 

Misc. Reloading Tools

Description
Product #
Price

Bullet Comparator 17, 20, 22, 27, 30, 33 Calibers

Measures from the major diameter of a bullet to the case head, rather than from the bullet's tip to the case head " Steel comparator has six holes cut, one for each caliber listed

Technical Information

Notes: Allows a comparative measurement from the major diameter of a bullet to the case head, rather than measuring from the bullet's tip to the case head Comparator is steel and has six holes cut, one for each caliber listed Insert a cartridge into its correct size hole, then measure from the opposite face of the tool to the base of the cartridge. This dimension may be used to adjust seating dies so that the bullets are being seated more uniformly with respect to the bullet's ogive rather than a cartridge's overall length.

365474

Bullet Comparator 17 - 33 Caliber

$19.99

Bullet Comparator 22, 24, 25, 26, 28, 30 Calibers

Measures from the major diameter of a bullet to the case head, rather than from the bullet's tip to the case head " Steel comparator has six holes cut, one for each caliber listed

Technical Information

Notes: Allows a comparative measurement from the major diameter of a bullet to the case head, rather than measuring from the bullet's tip to the case head Comparator is steel and has six holes cut, one for each caliber listed Insert a cartridge into its correct size hole, then measure from the opposite face of the tool to the base of the cartridge. This dimension may be used to adjust seating dies so that the bullets are being seated more uniformly with respect to the bullet's ogive rather than a cartridge's overall length.

746974

Bullet Comparator 22 - 30 Calibers

$19.99

Full Length Bushing Sizer

Sizer Die

 

Sizer die has a shorter OAL for better shoulder bump-back, and tighter internal tolerances. All of our standard sizer dies include a shoulder datum collar to measure shoulder bump and headspace. This include a pin retainer should you chose to use your sizer without the expander. The wide knurling on the die and lock ring make small hand adjustments.

 

height="222"

$78.99

PTG Quick Change Die Blank Lathe Fixture

Full Length Bushing Sizer and Micrometer Seater Set

 

Seater Die

 

For precise, consistent OAL handloads, the internals are designed to keep your rounds …. Round. Inside there is a floating sleeve system to improve concentricity – a must for repeatable precision. The micrometer adjustable seating die has wide knurling for precise hand adjustment at the loading bench. The depth increments are easily read and will stay that way for years of use.

 

 

Sizer Die

 

Sizer die has a shorter OAL for better shoulder bump-back, and tighter internal tolerances. All of our standard sizer dies include a shoulder datum collar to measure shoulder bump and headspace. This include a pin retainer should you chose to use your sizer without the expander. The wide knurling on the die and lock ring make small hand adjustments.

 

Bullet Comparator 22 - 30 Calibers

$178.99

PTG Quick Change Die Blank Lathe Fixture

Micrometer Seater

Seater Die

For precise, consistent OAL handloads, the internals are designed to keep your rounds …. Round. Inside there is a floating sleeve system to improve concentricity – a must for repeatable precision. The micrometer adjustable seating die has wide knurling for precise hand adjustment at the loading bench. The depth increments are easily read and will stay that way for years of use.

Hornady Chamfer and Duburring Tool

$115.99

PTG Quick Change Die Blank Lathe Fixture

Bullet Pointing Die System with #1 insert.

One of the most inconsistent and least utilized part that we have access to is the bullet tip. The solution the bullet pointing die.

A bullet pointing die is a die used to make a sharper point on a bullet. By doing this, we have made the bullet fly more efficiently resulting in less drop and wind drift. Who can benefit from this? Pretty much every rifle shooter who shoots at longer ranges can.

 The most inconsistent surface on a bullet is the tip. The 1000 yard benchrest shooters have developed a solution. It has become popular to trim the Bullet tip in recent years so that each one has exactly the same shape at the Bullet tip. Undoubtedly this has made the bullets more consistent and resulting in tighter groups.

With a bullet pointing die, we can make the Bullet tip smaller rather than bigger. Consider that a little pointing will do a lot of good. Typically with the bullet pointing die, we can close the Bullet tip up to about half of its original diameter. Here’s the kicker-by closing it to half of the diameter, the surface area is only one fourth of its original amount. This is the reason the pointing die is so effective.

30 to .700 Chamfer and Deburring Tool

$220.00

PTG Quick Change Die Blank Lathe Fixture

Bullet Pointing Die System No insert.

An insert and a caliber specific sleeve must be bought separately.

One of the most inconsistent and least utilized part that we have access to is the bullet tip. The solution the bullet pointing die.

A bullet pointing die is a die used to make a sharper point on a bullet. By doing this, we have made the bullet fly more efficiently resulting in less drop and wind drift. Who can benefit from this? Pretty much every rifle shooter who shoots at longer ranges can.

 The most inconsistent surface on a bullet is the tip. The 1000 yard benchrest shooters have developed a solution. It has become popular to trim the Bullet tip in recent years so that each one has exactly the same shape at the Bullet tip. Undoubtedly this has made the bullets more consistent and resulting in tighter groups.

With a bullet pointing die, we can make the Bullet tip smaller rather than bigger. Consider that a little pointing will do a lot of good. Typically with the bullet pointing die, we can close the Bullet tip up to about half of its original diameter. Here’s the kicker-by closing it to half of the diameter, the surface area is only one fourth of its original amount. This is the reason the pointing die is so effective.

30 to .700 Chamfer and Deburring Tool

$178.00

PTG Quick Change Die Blank Lathe Fixture

Sleeve for Bullet pointing System

 

Enter Caliber when purchasing to ensure we ship the correct item.

height="222"

$42.00

PTG Quick Change Die Blank Lathe Fixture

Bullet Pointing Die insert #0

height="222"

$42.00PTG Quick Change Die Blank Lathe Fixture

Bullet Pointing Die insert #1

height="222"

$42.00

PTG Quick Change Die Blank Lathe Fixture

Bullet Pointing Die insert #2

height="222"

$42.00

PTG Quick Change Die Blank Lathe Fixture

.17 to .45 Caliber Chamfer and Deburring Tool

The PTG Chamfer and Deburring tool is the ideal tool to chamfer the inside and deburr the outside edge of cartridge cases when they are new or after they have been trimmed. This crucial step removes slight imperfections from the case mouth causing increased seating consistency and reduces the chance of shaving material off of a bullet when it is being seated.

 

742818

Hornady Chamfer and Duburring Tool

$12.99
.30 to .700 Caliber Chamfer and Deburring Tool

N3861024

30 to .700 Chamfer and Deburring Tool

$15.00

Dual Pilot Caliber Chamfer and Deburring Tool.

Choice of standard bushing sizes.

The PTG Chamfer and Deburring tool is the ideal tool to chamfer the inside and deburr the outside edge of cartridge cases when they are new or after they have been trimmed. This crucial step removes slight imperfections from the case mouth causing increased seating consistency and reduces the chance of shaving material off of a bullet when it is being seated.

30 to .700 Chamfer and Deburring Tool

$65.00

PTG Quick Change Die Blank Lathe Fixture

Trimmer Base for L.E. Wilson Case Trimmer

This base is constructed of aluminum and measures 5 1/4" x 3" x 1 3/4".

Technical Information

Material: Aluminum Dimensions: 5 1/4" x 3" x 1 3/4"

889310

Trimmer Base for L.E. Wilson Case

$16.49

~Category Top~

 

~Top of Page~

 

More Products Coming Soon!

 

~Category Top~

 

~Top of Page~

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Quick Change Die Blank Lathe Fixture

 

PTG Quick Change Die Blank Lathe Fixture

 

 

Part# N3861367

 

$125.00

PTG Quick Change Die Blank Lathe Fixture


Die Blanks - Universal & Caliber Specific

Die Blank - Oblique
Die Blank - Side
Die Blank - Oblique
Die Blank - Side

 

~Top of Page~

  • Die Blanks

  • More
    Coming Soon!

Die Blanks

Die has a caliber specific pilot hole and is threaded on the bottom, knurled on top. This is the same style die as used by RCBS and other manufactures. 7/8" x 14 Thread. Die blanks allow you to cut a die for a custom chamber dimension or to create a new die for a wildcat cartridge. They must be reamed with a die reamer (sold separately) and are pre drilled with a pilot hole.

Standard 7/8 x 14 threads to fit most popular reloading presses.

  • Technical Information
  • Material: 4140 chrome moly steel
  • Dimensions: Length = 3.875" Width = 3/4"
  • Features: Standard 7/8" x 14 Thread Size Knurled Upper

Notes: Not a finished die. Must be reamed to the cartridge specifications of your choice. Upper end must be drilled and tapped for internal die parts such as the decapping/expander unit as well as the seater stem (available from RCBS). Lock ring for setting the die for a desired cartridge length not included (available from RCBS). Pilot hole of listed caliber drilled through die body Die body is made of the same material as used by RCBS and other manufacturers. Heat treating is generally not necessary as the die body will last a long time after cutting to the correct dimensions, as the body will then only have contact from the brass cartridge cases. However, if heat treating is desired, heat to 1650 - 1700° and then allow to cool slowly for 3 to 6 hours.

 

Description
Product #
Price

.17 Caliber Pilot Hole Die Blank 7/8"-14 Thread

529842

17 Caliber Pilot Hole Die Blank

$19.99
.20 Caliber Pilot Hole Die Blank 7/8"-14 Thread

656764

17 Caliber Pilot Hole Die Blank

$19.99
.22 Caliber Pilot Hole Die Blank 7/8"-14 Thread

314361

17 Caliber Pilot Hole Die Blank

$19.99
.25 Caliber Pilot Hole Die Blank 7/8"-14 Thread

512398

17 Caliber Pilot Hole Die Blank

$19.99
.270 Caliber Pilot Hole Die Blank 7/8"-14 Thread

670952

17 Caliber Pilot Hole Die Blank

$19.99
.30 Caliber Pilot Hole Die Blank 7/8"-14 Thread

118810

17 Caliber Pilot Hole Die Blank

$19.99
.338 Caliber Pilot Hole Die Blank 7/8"-14 Thread

124719

17 Caliber Pilot Hole Die Blank

$19.99
.358 Caliber Pilot Hole Die Blank 7/8"-14 Thread

823589

17 Caliber Pilot Hole Die Blank

$19.99
.375 Caliber Pilot Hole Die Blank 7/8"-14 Thread

269691

17 Caliber Pilot Hole Die Blank

$19.99
.45 Caliber Pilot Hole Die Blank 7/8"-14 Thread

493416

17 Caliber Pilot Hole Die Blank

$19.99
6.5mm-264 Caliber Pilot Hole Die Blank 7/8"-14 Thread

786397

17 Caliber Pilot Hole Die Blank

$19.99
6mm-243 Caliber Pilot Hole Die Blank 7/8"-14 Thread

744472

17 Caliber Pilot Hole Die Blank

$19.99
7mm-284 Caliber Pilot Hole Die Blank 7/8"-14 Thread

110332

17 Caliber Pilot Hole Die Blank

$19.99
Unpiloted Die Blank (Universal) 7/8"-14 Thread

444951

17 Caliber Pilot Hole Die Blank

$12.50

~Category Top~

 

~Top of Page~

 

More Products Coming Soon!

~Category Top~

 

~Top of Page~