Login
Register
home
Shopping Cart
0
Items -
$0
(541) 826-5808
0
Items
Toggle navigation
Reamers & Cutters
Chamber Reamers
Elliot Cutting Tools
Chamber Reamer & Gauge Specials
Muzzle Brake / Throat / Neck Reamers
Shotgun Form Tools
Barrel Breech Tools
Barrel Center and Crown Tools
Fluting Cutters
Barrel Counterbores
Core Drills
Bore Reamers
Carbon Ring Removal Reamers
Airgun - Pellet Reamers
Rifling Cutters
Cartridge Reamers
Scope Ring Alignment Reamers
Screw Counterbores
Slot and Groove Cutters
Firing Pin Hole Reamers
Radius, Dovetail & Form Cutters
Replacement Reamer Rings and Screws
Services
Gauges & Bushings
Headspace Gauges
Function Gauges / Cartridge Gauges
Bushing Adapters for Chamber Reamers
Firing Pin Indent Gauges
Receiver Raceway Gauge Pins
AR Gauges
Reloading Gauges
Erosion Gauges
Precision Bore & Chamber Check Gauges
Shotgun Gauges
Other Precision Gauges
Action Blueprinting Bushings
Reamer / Barrel Tool Bushings
Shotgun Pilot Bushings
Storage Tubes
Other Bushings
Gunsmithing
Specialty Tools By Manufacture
Reamer Holders
Reamer Parts, Tools & Stops
Wrenches, Jigs & Fixtures
Action Blueprinting
Action Mandrels & Lathe Centering Bars
Bolt & Firing Pin Tools
Misc. Gunsmith Tools \ Accessories
Punches
Reamer \ Cutter Handles
Recoil Lug Fixtures & Tools
Reloading Tools
Barrel Tenon Thread Protectors
Cutting Fluid & Lubrication
Shotgun Tooling
Bedding Columns & Compounds
M1 Garand Tooling
M2 Browning Tooling
M14 Tooling
M240 Tooling
Firearm Parts
Actions
Stocks, Chassis, Slings & Things
Remington & Clone Parts
AR15/AR10
Benelli
Browning
CheyTac
CZ
Dakota Arms
Howa, Weatherby, Nosler
Marlin
Mauser
Mossberg
Ruger
Sako
Savage Arms
Stiller
Thompson Center
Tikka
Winchester
Benchrest Accessories
Magazines, Mag Boxes, Followers
SPacific Trigger
Misc
Apparel \ Stickers
DVDs and Books
Misc
Home
Reamers & Cutters
Chamber Reamers
PTG Pull-Through Chamber Reamers
300 Winchester Magnum SAAMI Headspace Pull Through Reamer - HSS
300 Winchester Magnum SAAMI Headspace Pull Through Reamer - HSS
0
Review(s)
0
0
5
Write a Review
Your Price:
$219.00
Part Number:
PTG-13752-
Availability:
In Stock.
Choose Options
Add 36 Drive Rod
*
Add 36 Drive Rod
No Rod
Drive Rod - 36 (+$33.00)
Put me on the Waiting List
Quantity
+
-
Add to Cart
Description
If bare reamer is in stock, drive rods can usually be added within a weeks time. A finish reamer designed to remove the last few thousandths from a "short chambered" barrel to properly headspace the rifle. The reamer is inserted into the chamber, allowing the bolt to push on the back of the reamer. A drive rod is threaded into the reamer, inserted from the muzzle and turned from the muzzle end. Finish ream the chamber until the bolt lugs drop-in for perfect headspace.
Insert the reamer into the pre or short chamber. Make sure the bushing is on the end of the reamer then screw the drive rod into the pilot of the headspace cutter after carefully slipping the drive rod down the barrel. Rotate the cutter with forward pressure applied to the bolt. Once the bolt rolls over and locks, clean the chamber and check headspace.
Base-to-shoulder length is minimum spec. If the headspace reamer is used properly the headspace in the rifle will fall within .001 inches of minimum.
It is important to check headspace as soon as the bolt is fully locked. If you continue turning the cutter after the bolt locks the bolt return spring will continue to apply forward pressure on the cutter and cause it to cut until the bolt lugs bottom on the front of the bolt lug recess. This will result in excess headspace.
Caution: The reamer pilot is drilled and tapped for the drive rod so be careful not to apply excessive torque. Some barrels may have small bores and it may be necessary to grind pilots down. The standard thrust bushing thickness is .250". NOTE: Drive rods may exhibit slight surface rust. This in no way affects the performance of the reamer itself. It is recommended that drive rods be wiped down with a light oil prior to use. If bare reamer is in stock, rods can usually be added within a weeks time.
NOTE: All PTG Reamers and Cutting Tools are designed to work with petroleum-based lubricant. Water-based lubricant can give acceptable results, however the life of the tool will be reduced. For best results use petroleum-based lubricant.
×
Menu Links
Categories